To ensure your safe operation, please strictly in accordance with the provisions of this manual.
1. To avoid personal injury, it is strictly forbidden to open the door or cover when barrier working.
2.The barrier housing must be connected to the ground to prevent inductive electric shock.
3.It is strictly forbidden to stand, walk or place objects under the boom/ arm when barrier working.
4.The boom/arm and the spring have been matched to the balance state before goods leave out our factory. To avoid the danger of the balance being lost, the length and weight of the boom/arm can not be increased or decreased at random. If you need to change it, please ask the professional for advice.
This manual is copyrighted and may not be copied, cut, or modified without permission. Once found, the company will retain the contents of the manual without prior notice
Product Overview
The 2nd generation brushless non-spring barrier gate is a breakthrough technology that solves the technical problem of traditional barrier gate requiring spring balance to operate smoothly and achieve sufficient torque. The 2nd generation brushless non-spring barrier gate uses the latest developed inflatable arm, which is lightweight, fast in operation, and can ensure long-term stable operation even for long barrier arm. The inflatable arm also solves many other problems: 1. Convenient transportation (greatly reducing the cost of transportation; 2. Lightweight (greatly improving the lifetime of the barrier motor and reducing the failure rate, especially for non-spring motor with absolute advantages); 3. Not afraid of car collisions and typhoons damaging the barrier arm; 4. Truly achieving no harm to the car and people.; 5. Saves storage space and rent. The 2nd generation brushless non-spring barrier gate adopts the industry’s most fashionable design of a one-piece barrier housing without cover, with integrated mechanical and electrical design, left and right direction can be quickly interchanged, Fifth-level gear large speed ratio design, large torque and high efficiency, can bear 6m two fence arm, respond immediately at any angle without jerking. The high-power and high-torque permanent magnet rare earth DC brushless motor design, ultra-intelligent driver, and intelligent release of reverse voltage without damaging components can completely achieve a military-grade life span of more than 5 million times. Truly achieve high-end products that are safe, stable, reliable, durable, innovative, and of high quality!
Parameters of Barrier Arm Type,Length and Operation Speed
Functions
- Operation speed can be adjusted.
- Slow up and slow down can be adjusted.
- The limit angle can be adjusted.
- Left and right direction can be quickly interchanged.
- The barrier arm can be manually operated in case of power
failure. - 418 frequency learning code anti-copy remote controller.
- Infrared photocell sensor IO signal input function.
- Loop detector and radar IO signal anti-collision signal input
function. - Up, down and stop IO signal input function.
- Counting (fleet) function.
- LED light IO signal output function.
- Traffic light IO signal output function.
- Up and down in place, normally open and normally closed
signal output function. - RS485 communication output function.
- Delay arm drop function.
- Arm auto-reverse function.
- Automatic lifting function when power is off (requires
additional power storage module). - IO port single-key cycle up and down function.
- Loop detector normally open and normally closed function.
- One car and one arm to prevent toll evasion function.
- Anti-collision alarm function (requires additional fee,
installation of alarm and sensor). - Fire linkage signal input function.
- The IO port closes the signal input function.
- 24V storage battery input function.
Technical Parameters
- Working temperature(motor): -35℃~+65℃
- Rated Supply：24/100/240VAC,50/60Hz
- Running speed：6sec to 17Sec(adjustable)
- Rated power：350W
- Driving Method：DC Brushless Motor
- Humidity：≥90%
- Remote control distance：≤100M（open,sunny weather）
- IP Degree：IP54
- Motor No-load Speed：1850r/min
- Max Boom Length：6M-8M
The 2nd generation brushless non-spring motor mechanism
Product Size and Arm directions definition
Installation, commissioning and use
1、Equipment installation
1. Please select the correct type of barrier gate according to the specifications of the pace,and then fix the barrier cabinet with expansion bolts.
After determined the position,the barrier gate foundation should be done according to the site conditions,and also make the cast-in-place basement for the non-concrete ground.
2、Adjust the Position of Barrier Arm
To adjust the position of the arm (for example, after exerting excessive force), please take the steps as below:
- open the barrier gate door and remove the cover
- Loosen the two fastening screws of the DZ-8 on the pendulum shaft with an M12 Allen key, so that the barrier arm can be repositioned by hand.
- Calibrate the position of the barrier arm (horizontal position, as shown in Figure 1).
- Use a hexagon wrench to re-tighten the two fastening screws
3、Barrier arm balance adjustment
- Please check and confirm arm status in horizon and vertical position，then tighten 2pcs M12 screw.
- According to arm balance status, repeat adjusting the spring level of tightness of M8*140MM, make sure the arm open and close in stable.
- For the barrier gate with double springs,please adjust the two springs simultaneously.
- If arm open and close shake too much, Please check below picture. Open arm shaking a lot means spring is too tight, loose a little. Close arm shaking too much means spring too lose, repeat tighten a little spring.
4、Electrical installation, wiring diagram
- The internal wiring of this machine has been completed when it leaves the factory, please do not change it, just connect the 220V power supply and the protective ground wire to work.
- Traffic light interface: 2A24V voltage traffic light use.
- Infrared anti-smashing interface: external infrared anti-radiation device, and the switch signal of the anti-radiation output can be connected.
- Ground sense interface: support external ground sense. When using an external ground sensor, you only need to connect the switch signal output by the ground sensor.
- Parking system interface wire control interface: connect the switch signal from the system to this interface to control the barrier.
- Starting limit and landing limit signal output: output COM/NO/NC switch signal to the system to inform the current state of the barrier.
- RS485 or CAN communication interface: PC software can be used to manage more than 15 barriers.
5、Function setting description
When setting the function, please press the menu button on the control panel. The Nixie tube displays H00-00 or H00-other numbers. We correspond to the function parameter table code to enter the required function parameter setting. For example, H00-00 is the UP ARM speed adjustment, and then press the confirm button Enter the parameter setting, the number will be displayed on the digital tube, then press the up or down key to set the required UP ARM speed number, and then press the confirm button to complete the ARM-up speed setting.
The other function settings are the same as the example settings.
Function setting parameter table
6、Error code
7、Learning type remote control
The remote control using special IC learning code remote controller, 418MHz wireless frequency, strong anti-interference, long remote control distance, that can up to 100meters in good weather, use easily and durable. The receiver of learning code remote control can store 16 different remote control codes, and support unlimited number of same code remote control. The external receiver learned the remote control within 5 seconds when power on,press the open/close key at the same time to complete the learning, and reset to continue learn when not complete. If repeat the learning, open the external receiver shell, there is a white button on circuit board, hold down 15 seconds to delete the remote control code, continue to learn or press the white button to learn.
Arm length speed comparison table
Service Items
1 One year’s free servicing is supplied(not including the arm);
2 Lifetime charged servicing is offered;
3 Technology servicing is supplied.
The following situations are charged for servicing(or changing):
1 Broken by the wrong installation.
2 Broken by improper voltage.
3 The surfaces of the system destroyed by wrong installation or use.
4 Broken by natural disaster.
5 Overdue.
6 Servicing items out of our promises.
Product Maintenance
1 Keep the barrier gate clean
2 Check the joints ever month in case of any loose parts.
3 Check the spring elasticity after the barrier gate running 3000 times.
4 Check the easily worn-out parts(like the spring,limit switch),every half year and renew it.
5 Remote control distance will be shortened or not work in case like big object screening,battery exhausting,extreme weathers.
Packing List
Appendix
