To ensure your safe operation, please strictly in accordance with the provisions of this manual.
This manual is copyrighted and may not be copied, cut, or modified without permission. Once found, the company will retain the contents of the manual without prior notice
Product Overview
Thank you for purchasing our company’s Zhidrive Springless Power Brushless Barrier. This product is a typical mechatronics product. It has the characteristics of small size, low noise, high efficiency, wide speed regulation, and small steady-state speed error. The springless reduction box is dedicated to the gate, multi-speed ratio can be selected, the operation is stable, the special gear transmission has higher efficiency and high stability, and is more and more respected by the market. It adopts the latest mold design technology, mold die-casting manufacturing technology, and brushless control constant Force algorithm technology, fast interchangeable left and right, no clutch design, more reliable quality, more convenient to use, the movement adopts four-stage gear transmission, large torque, long life, high efficiency, curved crank arm three-link structure, landing rod Fast and stable, self-locking in place, easy maintenance.
Parameters of Barrier Arm Type,Length and Operation Speed
Functions
- The running speed can be adjusted from 1.2s to 3s,2.5s to 8s.
- Arm direction can be quickly interchanged
- Open the barrier gate by motor wheel when power off ,automatically reset after power on
- Curved crank arm three- link movement structure, the operation is stable
- Wireless remote control control open/close
- Auto reverse function（force adjustable）
- Infrared photocells connector is available
- Loop detector connector is available.
- Well-integrated with car parking system equipment,with wire control(must be switch signal)
- Connector for traffic light(AC220V,power less than 40W)
- Offering dry contact signal for car parking system(COM,NC,NO)
- Auto-delay when closing(adjustable)
- RS485 or CAN network communication interface（no need to install module）
- Counting interface
- 24V backup battery interface（Can be charged by using solar energy)( optional)
- Auto-open when power-off (installation of power storage module) (optional)
- Anti-collision alarm device (optional)
- Loop detector normally open and normally closed signal selection
- One car and one open (fee evasion function)
- Special signal input for fire protection
Technical Parameters
The first
- Working temperature(motor): -25℃~+60℃
- Rated Supply：24/100/240VAC,50/60Hz
- Running speed：1.2sec to 3Sec(adjustable)
- Rated power：200W
- Driving Method：Brushless motor
- Humidity：≥85%
- Remote control distance：≤50M（open,sunny weather）
- IP Degree：IP54
- Motor No-load Speed：1800r/min
- Max Boom Length：3M Straight arm
- Deceleration ratio：1:50
the second
- Working temperature(motor): -25℃~+60℃
- Rated Supply：24/100/240VAC,50/60Hz
- Running speed：2.5sec to 8Sec(adjustable)
- Rated power：200W
- Driving Method：Brushless motor
- Humidity：≥85%
- Remote control distance：≤50M（open,sunny weather）
- IP Degree：IP54
- Motor No-load Speed：1400r/min
- Max Boom Length：Straight arm 6M、90°Folding arm 5M、180°Folding arm 4.5M、Two fence arm 4.5M、Three fence arm 4M
- Deceleration ratio：1:150
mechanism parts’ name of barrier gate without spring
Product Size and Arm directions definition
Installation, commissioning and use
1、Equipment installation
1. Please select the correct type of barrier gate according to the specifications of the pace,and then fix the barrier cabinet with expansion bolts.
After determined the position,the barrier gate foundation should be done according to the site conditions,and also make the cast-in-place basement for the non-concrete ground.
2、Calibrate the barrier gate arm position
To calibrate the position of the barrier arm (for example, after applying excessive force), proceed as follows:
- First determine the horizontal and vertical state of the brake lever, then tighten 1 M12 locking screw on the swing arm, then lock the 2 M8 screws on the upper side of the anti-skid device, and finally lock the M10 screw on the anti-skid device to adjust horizontally. Done!
3、Electrical installation, wiring diagram
- The internal wiring of this machine has been completed when it leaves the factory, please do not change it, just connect the 220V power supply and the protective ground wire to work.
- Traffic light interface: 2A24V voltage traffic light use.
- Infrared anti-smashing interface: external infrared anti-radiation device, and the switch signal of the anti-radiation output can be connected.
- Ground sense interface: support external ground sense. When using an external ground sensor, you only need to connect the switch signal output by the ground sensor.
- Parking system interface wire control interface: connect the switch signal from the system to this interface to control the barrier.
- Starting limit and landing limit signal output: output COM/NO/NC switch signal to the system to inform the current state of the barrier.
- RS485 or CAN communication interface: PC software can be used to manage more than 15 barriers.
4、Function setting description
When setting the function, please press the menu button on the control panel. The Nixie tube displays H00-00 or H00-other numbers. We correspond to the function parameter table code to enter the required function parameter setting. For example, H00-00 is the UP ARM speed adjustment, and then press the confirm button Enter the parameter setting, the number will be displayed on the digital tube, then press the up or down key to set the required UP ARM speed number, and then press the confirm button to complete the ARM-up speed setting.
The other function settings are the same as the example settings.
Function setting parameter table
5、Error code
6、Learning type remote control
The remote control using special IC learning code remote controller, 418MHz wireless frequency, strong anti-interference, long remote control distance, that can up to 100meters in good weather, use easily and durable. The receiver of learning code remote control can store 16 different remote control codes, and support unlimited number of same code remote control. The external receiver learned the remote control within 5 seconds when power on,press the open/close key at the same time to complete the learning, and reset to continue learn when not complete. If repeat the learning, open the external receiver shell, there is a white button on circuit board, hold down 15 seconds to delete the remote control code, continue to learn or press the white button to learn.
Arm length speed comparison table
Service Items
1 One year’s free servicing is supplied(not including the arm);
2 Lifetime charged servicing is offered;
3 Technology servicing is supplied.
The following situations are charged for servicing(or changing):
1 Broken by the wrong installation.
2 Broken by improper voltage.
3 The surfaces of the system destroyed by wrong installation or use.
4 Broken by natural disaster.
5 Overdue.
6 Servicing items out of our promises.
Product Maintenance
1 Keep the barrier gate clean
2 Check the joints ever month in case of any loose parts.
3 Check the spring elasticity after the barrier gate running 3000 times.
4 Check the easily worn-out parts(like the spring,limit switch),every half year and renew it.
5 Remote control distance will be shortened or not work in case like big object screening,battery exhausting,extreme weathers.
Packing List
Appendix
